Honeywell aquastat l6006a manual

On by hayward cull - how do you hook the LA up- what wires goes onwhat screw. I have my aquastat set at and it shuts off before and don't turn on until it gets to My dif is set at What could the problem be? Al I would not expect a new aquastat to make water hot again - we need a more-thorough diagnosis of the problem.

For example, scale clogging can reduce hot water quantity and temperature; A poorly-mounted aquastat temperature sensor or one lacking the heat conductive grease in a sensor well could cause the aquastat to fail to sense water temperature properly.

Let's get a service tech on site. Wood fired boiler with a aquastat. Only running a selonoid to open and close a dampener How do we wire. It to do ,this.

Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly. Note: appearance of your Comment below may be delayed: if your comment contains an image, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator.

Apologies for the delay. We provide links just below to several aquastat installation, setting, and adjustment documents in response to reader requests and comments that people sometimes have difficulty finding this information. But readers looking for specific aquastat control information should always first try the control manufacturer. Just ask us! Search the InspectApedia website. Comment Form is loading comments Bottini Fuel is a residential and commercial heating oil distributor and oil heat service company in Wappingers Falls, NY and with offices in other New York locations.

Typical timer applications will cycle the pump at preset times, allowing the user to select operation of the circulating pump during high peak usage periods in order to decrease the delivery time to outlet fixtures and reduce wasted water, also available at www. These newer aquastat controllers are often used to replace the older Honeywell LA series that was and remains widely used, also available at www.

LU is a universal electronic aquastat replacing over 40 other aquastat models that provides circulator, burner and boiler temperature control with electronic temperature sensing. The LU provides status and diagnostic information through an LED display to enhance the diagnostic process. In "Run" mode the LED displays the boiler temperature followed by the ambient temperature.

Buttons inside the control permit the service tech to scan through the control's settings as well as to change them, much like the functions on a programmable room thermostat. Five diagnostic LEDs inside the control provide additional diagnostic features, indicating counterclockwise from upper left EnviraCOM network active, Thermostat calling for heat, Burner on, Power to zone circulator interrupted lockout , Circulator powered.

This is a "triple aquastat" providing High, Low, and circulator controls, as well as advanced features permitting electronic configuration and an LED display for diagnostics. This aquastat can provide multiple zone control as well. The low-limit can be disabled for "cold-start" boiler applications such as where no tankless coil is in use. National Fuel Gas Code Z Catalog XHO Immersion Well: psi kPa.

If you have additional questions, need further information, or would like to comment on our products or services, please write or phone:. International Sales and Service Offices in all principal cities of the world.

Remote bulb devices and well-mounted devices shipped without well are component recognized:. MP, Guide No. LG is listed: File No. E, Guide No. Canadian Standards Association: File No.

Horizontal and vertical models mount directly to an immersion well installed in a boiler fitting. LH and LC contain a bracket and clamp for surface mounting on the pipe or tank.

Remote bulb models have three mounting holes. The LB direct immersion model also mounts directly to a boiler fitting. See form no. Approximate case installation dimensions in inches mm for direct insertion models.

Approximate installation dimensions in inches mm for remote bulb models. Other dimensions are the same as Fig. Approximate installation dimensions in inches mm for surface mount models. Approximate immersion well dimensions in inches mm for all models except LC and LB. Approximate boiler fitting and bulb dimensions in inches mm for LC and LB.

Table 1. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.

Please check your email for further instructions. Enter a new password. Contents General Vertical or horizontal mount. Switching: L, L, L Spst. Sensing Bulb Material: Copper.