Jbl lsr4326p manual

I just have a small little room to mix down I like my JBLs. For more information, seeAppendix E on page 38 in this manual. Need it now but short of cash? Reinforced for Mounting Reinforced mounting points on each speaker ksrp convenient positioning and installation of multi-channel surround systems for any mixing application, in any environment.

I plan on keeping these for many years to come barring any huge issues such as completely failing on me or exploding for some reason: It was very clean sounding and seem to have the capability to sound nice but who ever set these up had them set up in such a way that it sounded so harsh. We automatically charge the payments to your credit card. EQ Presets Appendix A:. April 7, admin 0 Comments. All transducers are self-shielded, with Neodymium motor structures for exceptional transient response and superb power handling.

Unpack the speakers. To avoid damage to the speaker elements, open the top of the box, keep the Styrofoam end cap on, and roll the box upside down. The box can then be slipped off. This also works in reverse for repacking the units. Be sure to not grasp the monitors from the front. Position each speaker in the room.

See page 30 in this manual for speaker placement tips. Connect each speaker to a suitable power source using the suppliedAC power cable.

See page 23 in this manual for more information. Connect the speakers together in any order using the supplied CAT5 cable. Plug one end of the cable into either of the two HiQnet ports on one speaker and the other end into a HiQnet port on another speaker until all speakers are connected.

See page 21 in this manual for more information on networking your LSR monitors. Set the Network ID DIP switch on the rear panel of each speaker so that it corresponds to the channel for which the speaker is to be used. See page 22 in this manual for more information. Make all required audio connections to the rear panel of your monitors.

See page 23 in this manual for more information on audio connections. If you are connecting an analog signal i. See page 24 in this manual for a wiring diagram. If you are connecting digital signals i. All speakers in the system will power on the JBL Logo will go from dimly to brightly lit. All speakers in the system will go to the designated volume. As the volume is increased, additional LEDs light. To calibrate your speakers with RMC, begin by attaching the provided calibration microphone to a mic stand and place the mic at the mix position, oriented vertically.

Press and hold the RMC button on any speaker, then walk to a spot in the room where you are not blocking the path between the microphone and any speaker. You can compare the effects of RMC with the uncorrected response by pressing the RMC button on the front panel of any speaker. See page 25 in this manual for a step-by-step description of the RMC calibration procedure.

After pressing the RMC button, move away from the speaker. Finally, put on some good music to listen to and take a few moments to read the rest of this manual to acquaint yourself with all the features of your JBL LSR system. The controls and displays on the front panel of the LSR allow you to adjust and view various speaker settings.

Below is a listing and description of each. It is illuminated at full brightness when the speaker is powered up and active. Power —After connection to anAC power source, press this button to turn the speaker on. If networked together with other speakers, all speakers will turn on simultaneously. As shown below, when the speaker is powered on and active, the JBL logo will be brightly lit see 1 above and the left-most meter segment will be lit:.

Meter Display — In combination with front panel buttons, the meter is used to display the current setting and status of the following functions:. The meter has 31 three-color segments that can illuminate in green, amber or red. For many of the above operations, all 31 segments light green only. Green LEDs indicate signal 8 dB or more below clipping; amber, approximately 7 to 4 dB below clipping; and red, approximately 3 to 0 dB below clipping.

The LSR models include protective limiting. You can calibrate your LSR system so that the meter display will show how much SPL the speaker is contributing at the listening position. For more information, see Appendix E on page 38 in this manual.

Page 12 Quick Start8. I just hope somebody out in this fourm world that can give me an insight about how these pair of speakers work. Page 39 Appendix C: The results are a revolution in professional mixing: They have a seemingly flat response after sampling the room and they sound pretty good too. Reference — Front Panel9. After pressing the RMC button, move awayfrom jb, speaker. Page 40 Appendix C:. This website uses cookies to improve your experience while you navigate through the website.

Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.

We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent.

You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.

Skip to content. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish.